search JMRI:

Setup JMRI

• Preparing to Install

Getting Started

• What is DCC?
• What DCC systems will DecoderPro work with?
• What hardware do I need?
• How do I start the program?
• How do I start DecoderPro® program for the First Time User?
• How do I set up my Preferences?

Using DecoderPro

• How do I set up to program a decoder?

DecoderPro Programming Modes

• Single CV Programmer
• Service Mode Programmer
• Ops Mode Programming

The Basic Programmer

• Entering Locomotives in the "Roster"
• The basic programmer
• Reading the data from the decoder
• Entering and editing new data
• Writing the new data to the decoder
• Saving the new data to a file
• What if I need to do more?

The Comprehensive Programmer

• Setup and Roster Panes
• Expanded Basic Pane
• Motor Control Pane
• Speed Control Pane
• Speed Table Pane
• Function Mapping Pane
• Lights Pane
• Consisting Pane
• Advanced Features Pane
• Analog Controls Pane
• Sound Pane
• Sound Levels Pane
• Global CV Pane
• Manufacturer-Specific Pane
• Printing the Decoder Data

Advanced Features

• Function Labels Pane
• Roster Media

DecoderPro® Main Window

• Menu Bar
• Toolbar
• Roster Table
• Decoder Information
• Status Bar

Error Messages

• Error Codes explained

DecoderPro® Comprehensive Programmer

Consisting Functions Pane

---

Consisting is a means to have two or more locomotives respond to orders from the command station, and do it together in unison. There are a number of terms used to describe consisting, and the manufacturers don't agree what those terms should be. The NMRA has adopted terminology, so that is what will be used in this discussion.

Address Consisting. You merely set the address of every locomotive to be the same, and we can use the Basic Programmer pane to do this. Then a DCC instruction sent to a locomotive with address XX will cause all the locomotives with address XX to respond. It works well for locomotives that are always run together, and is portable from one layout to the other. The disadvantage is that it's a pain to keep re-addressing your locomotives if you don't always run them together.

So, the NMRA came up with two additional means of consisting. One is set up in, and remembered by the command station, and the other is set in the decoders.

The NMRA calls the command station based system Basic Consisting. The command station keeps a list of all the locos in the consist. When an action is needed the command station sends an individual packet to every locomotive in the consist, which causes them to then act together. Since this method is command station based the consist is not portable to another system. Also, since it does not need to be programmed into the decoders, DecoderPro doesn't need to deal with it.

The NMRA calls the decoder based system Advanced Consisting. To implement this system the decoder has to have a special memory space (CV19) which is used to store a consist address. This type of consisting is portable between layouts, since the information that the loco is part of a consist, and the address information for that consist is carried in the decoder. The disadvantage is that once the locomotive is assigned to a consist it will only respond to the consist address. If you forget to 'break' the consist at the end of an operation, you will be puzzled as to why your locomotive won't respond to requests for motion, even though it will respond to some of the lighting functions.

DecoderPro utilizes the Consisting Pane to set up NMRA Advanced Consists and the response of the locomotive to function requests sent to the consist address.

The Advanced Consist Address is for EPF (Extended Packet Format, as defined by the NMRA Recommended Practices for DCC). If the consist address is any value other than zero, the locomotive is considered to be in a consist and will only respond to instructions sent to the consist address. Thus we set a short address here to create a multiple engine group that will all respond to the same address. Think of it as an MU specific locomotive address. Since the address is in the same range as non-consisted locomotives with short addresses, we need to be sure the address is unique on the layout. A way of doing this is to use higher end of the short address range starting from 127 and going down. Most folks working with single locomotives with short addresses tend to be using the manufacturer's default of 3, or other low values, typically for their logging locomotives.

This Pane also allows one to instruct the decoder what effects are to be active when the locomotive is in a consist, assuming the decoder is capable of responding appropriately. As an example, this allows you to specify if the headlights and other lighting functions are to be always off if the locomotive is in the middle, or tail end. This can be handy if only the "B" unit has sound. You can set it's lights to be off in a consist, but it can sound it's horn even though it's in the consist.

If you've had your locomotives on another layout and ran them together, but can't get them to run separately on your home system, check this to see if it's consist address has been set.

---

---